ROLL-OUT AWNING (Car Side Tarp) Installation Manual

Please read the instruction manual carefully and use the product correctly and safely.
To use the ROLL-OUT AWNING safely, check the specifications of your vehicle, roof rack, and crossbars before installation.

1. Things to check before installation

Important: Improper installation or loose fasteners can lead to detachment or damage while driving. Always check the fastening condition not only after installation, but also before each use and before driving.

Product specifications and installation conditions

Pre-operation check

• Park in a level and safe location, and engage the parking brake.
• Confirm that the roof rack or crossbars are correctly attached to the vehicle.
• Check for a position that avoids interference with doors, tailgate, roof tent, and cargo.
• Confirm that all accessories are present.
• Do not fully tighten initially; adjust the position after a trial fit.

Regarding fire

• Keep flames and heat sources away from the tarp fabric.
• Do not use open flames or heating devices under or around the tarp.
• Make bonfires in a location away from the tarp and be careful not to let sparks touch the fabric.

2. List of accessories

Before installation, please check that all accessories are present in the correct types and quantities. If any are missing or damaged, do not proceed with installation and consult the retailer.

*Component names are aligned with the current instruction manual. Depending on the actual rack shape, separate components or brackets may be required.

3. Installation position and fastening method

The ROLL-OUT AWNING is secured at two points, front and rear, on the roof rack or crossbars. Check the rack shape and the presence of grooves, and select a position that does not interfere with the vehicle. Also check the permissible load capacity of the vehicle and the rack.

Caution during installation: Do not fully tighten during the trial fitting stage. Secure after checking for interference with doors, tailgate, roof tent, and cargo.

4. Vehicle installation procedure

1. Determine the fixing position on the rack side

Check for a position that allows sufficient deployment space on the side of the car body. Adjust the position of the rack or crossbars so that they can be secured at two points, front and rear.

2. Insert T-screws into the rack-side grooves

Slide the T-screws into the front and rear rack or crossbar grooves and temporarily place the L-brackets.

3. Insert bolts into the back of the main unit

Slide the four bolts into the aluminum slots on the back of the main unit and ensure that the bolt heads are held within the slots.

4. Connect the main unit and L-brackets

Adjust the bolt positions on the back of the main unit and pass them through the holes in the L-brackets. Temporarily secure the left and right brackets evenly.

5. Check for interference with the vehicle

Check for any interference with doors, tailgate, roof tent, and cargo. If there is a problem, adjust the front/rear position or height.

6. Tighten securely

If the position is correct, tighten all bolts evenly. After installation, check for any looseness in the main unit.

Important: After installation, always check for loose bolts and brackets before use and before driving.

5. Deployment procedure

1. Open the cover

Unsnap the outer cover buttons and open the cover. Loosen the hook-and-loop fasteners holding the main unit.

2. Pull out the tarp

Pull the tarp out of the aluminum frame and deploy the left and right frames.

3. Deploy the legs

Remove the two legs from the inside of the front beam and rotate them towards the ground. Adjust to the required height and lock them.

Caution: Rotate the legs down using the base as an axis, but do not rotate the black resin joint in the middle of the leg (this may cause damage).

4. Secure the arms

Insert the end pins into the corresponding holes, extend the arms, and connect them to the front beam. Secure the hook-and-loop fasteners and peg down the guy ropes.

Storage method

To store, follow the reverse order of deployment. Make sure the fabric and arms are securely stowed, close the cover, and fasten the snap buttons.

6. Checks during use, storage, and before driving

During use

• To prevent overturning, always peg down the guy ropes.
• In rainy weather, create an appropriate slope for water to drain.
• Store the tarp early before strong winds or rain.
• In snowy conditions, frequently remove snow to prevent the fabric from stretching.

During storage

• If stored wet, dry it as soon as possible.
• Check the fabric, frame, and cover for any abnormalities.
• Close the cover and securely fasten the snap buttons.

Before driving

• Check for any looseness in the L-brackets, T-screws, and bolts on the back of the main unit.
• Check for any rattling or unusual noises from the main unit.
• If you have any concerns about the stability of the installation, do not drive.

Strong winds/inclement weather: Store the tarp early before the weather worsens. Do not leave it set up unattended.

In case of malfunction: If you notice any damage, deformation, significant looseness, or unusual noises, discontinue use. Please refer to the purchase information and retailer's guide for warranty conditions and repair options.

7. Product page / Inquiries

Please check the product page for product size, color, dedicated annex room, extension wall, and stock status.

Regarding installation and compatibility

If you are unsure about the installation method, please contact us before purchasing, including information about your vehicle model, year, and the roof rack or crossbars currently installed. Information that is helpful for confirmation when contacting us:

• Vehicle model and year
• Manufacturer and model number of the roof rack or crossbars
• Photos of the rack's grooves or fastening points
• Other products installed simultaneously, such as a roof tent